Skip to main content

User Manual

Agaru Instructions and User Manual

Written by Jeremy Augment

Assembly (First Use)

Agaru E-Scooter User Manual

Applies to: Augment Agaru e-scooter
​

Important safety information

  • Wear appropriate protective gear before riding.

  • Use only the original Augment charger.

  • Never open, modify, or disassemble the battery or scooter.

  • Do not use a battery that is damaged, leaking, overheating, or otherwise abnormal.

  • Keep the battery away from children and pets.

  • Do not charge the battery in freezing temperatures.

  • Never clean the scooter with a pressure washer.

Scooter parts and component names

The main Agaru components are:

  • Headlight

  • Rear brake lever

  • Left and right turn indicators, also called blinkers

  • Left and right handlebar grips

  • Function button, also called the switch button

  • LED display

  • Thumb accelerator, also called the throttle

  • Stem, also called the head tube or pole

  • Folding lever, also called the folding spanner or folding wrench

  • Folding hook and rear-fender hook

  • Stop or limit block for the folding hook

  • Battery charging port, also called the battery DC port

  • Battery cover

  • Motor

  • Front disc brake

  • Kickstand

  • Deck screws

  • Anti-slip deck

  • Tail lights

Controls and buttons

Power and function button

Use the function button as follows:

  • Long press: Turn the scooter on or off.

  • One click: Change the ride mode. The modes are Walk mode (Gear 1), Normal mode (Gear 2), and Sport mode (Gear 3).

  • Two clicks: Show total mileage.

  • Three clicks: Show single-trip mileage.

  • Four clicks: Switch the speed and distance units between kilometers and miles.

  • Five clicks: Set the initial password. To change or cancel the password, press the button five times within five seconds after switching on the scooter.

  • Six clicks: Turn the cruise-control function on or off.

Headlight

Press the headlight button once to switch the headlight on or off.

Turn indicators

  • Press the left-indicator button once to switch the left blinker on or off.

  • Press the right-indicator button once to switch the right blinker on or off.

Throttle

Slowly press the thumb throttle to accelerate. The scooter must already be rolling before the motor engages.

Brake lever

Pull the rear brake lever to slow down or stop.

Cruise control

First make sure the cruise-control function is enabled through the function button. To activate cruise control while riding, maintain the same speed for at least six seconds. After cruise control activates, the scooter maintains speed without continuous throttle input. Press the throttle or use the brake to exit cruise control.

LED display symbols and information

The LED display can show:

  • Current speed

  • Speed unit: km/h or mph

  • Ride mode: Gear 1, Gear 2, or Gear 3

  • Battery level

  • Bluetooth status

  • Total or trip mileage; total mileage is marked ODO

  • Headlight status

  • Cruise-control status

  • Fault warning, shown with a wrench symbol

First-use assembly

The term handlebar assembly below refers to the part called the machine head in the original illustrated instructions. The term stem refers to the pole or head tube.

  1. Disengage the rear folding hook by moving the folded front section to the right. Raise the stem to the upright position, then securely close and tighten the stem locking lever.

  2. Firmly connect the white electrical plug between the handlebar assembly and the stem.

  3. Carefully tuck the connected wiring inside the stem. Do not pinch or damage the wire.

  4. Insert the handlebar assembly fully into the top of the stem.

  5. Align the six threaded holes in the handlebar assembly with the six holes in the stem.

  6. Install all six M5 × 12 screws. Tighten them with the wrench supplied in the tool kit until the handlebar assembly is secure and does not wobble.

How to fold the scooter

  1. Rotate the limit block on the handlebar hook 90 degrees clockwise.

  2. Locate the inner section of the folding lever near the base of the stem. Press firmly on the lower end until the upper end rises.

  3. While the upper end is raised, push it clockwise until the folding mechanism opens.

  4. Fold the stem down and angle it slightly to the right.

  5. Slide the front folding hook into the hook on the rear fender.

  6. Rotate the folding-hook limit block 90 degrees counterclockwise until it stops. This secures the scooter in the folded position.

How to ride the Agaru scooter

  1. Wear protective gear.

  2. Turn on the scooter.

  3. Place one foot on the deck and push forward with the other foot.

  4. Once the scooter is rolling, press the throttle gently.

  5. Place both feet on the deck, with your stronger foot toward the rear.

How to turn

  • Turn the handlebar slightly in the direction you want to travel.

  • Lean your body gently in the same direction to maintain balance.

How to slow down and stop

  1. Release the throttle to begin slowing down.

  2. Pull the brake lever to stop.

  3. When the scooter comes to a complete stop, place one foot on the ground.

Battery safety and storage

Always follow these battery rules:

  • Use only the original Augment charger.

  • Keep the battery away from children and pets.

  • Never open or modify the battery.

  • Do not use a battery that is damaged, leaking, overheating, or otherwise abnormal.

  • Do not charge the battery in freezing temperatures.

  • Charge the battery at least once a month. Never leave a stored battery uncharged for more than three months.

  • Store the scooter and battery in a dry place.

How to charge the battery

The battery can be charged while attached to the scooter or after removal.

  1. Turn off the scooter.

  2. Open the rubber charging-port cover.

  3. Confirm that the charging port is clean and dry.

  4. Plug the charger into the wall outlet.

  5. Connect the charger to the battery.

  6. Check the charger light. Red means charging; green means fully charged.

  7. When charging is complete, disconnect the charger and close the charging-port cover.

Maintenance and cleaning

  • Check the tire pressure regularly.

  • Clean the scooter only with a soft or microfiber cloth.

  • Never use a pressure washer.

  • Store the scooter and battery in a dry place.

  • Keep the battery charged during storage; charge it at least monthly and never allow more than three months between charges.

  • Do not disassemble the scooter yourself.

Package contents

The package should contain:

  • Agaru e-scooter

  • Charger

  • User manual

  • Tool kit

If an item is missing or damaged, contact Augment support immediately.

Did this answer your question?